Virology & Mycology Infectious Diseases

Search :   Advanced Search 

Home   |   Join   |   Contact     

   
Journal Details
 
Article usage
Total views: 0
[From(publication date):
-- Nov 23, 2014]
Breakdown by view type
HTML page views :
PDF downloads :
XML downloads :
 
 
 
 
 
Research Article Open Access
Development and Characterization of Solid-Lipid Microparticles of Highly Insoluble Drug Sirolimus
Department of Pharmaceutics, KLE University College of Pharmacy, Belgaum, India
*Corresponding author: Dr. Basavaraj K. Nanjwade
Department of Pharmaceutics
KLE University College of Pharmacy
Belgaum, India – 590010
Tel: 00919742431000
Fax: 00918312472387
E-Mail: bknanjwade@yahoo.com
 
Received December 07, 2010; Accepted January 24, 2011; Published February 01, 2011
 
Citation: Nanjwade BK, Patel DJ, Parikh KA, Nanjwade VK, Manvi FV (2011) Development and Characterization of Solid-Lipid Microparticles of Highly Insoluble Drug Sirolimus. J Bioequiv Availab 3: 011-015. doi:10.4172/jbb.1000050
 
Copyright: © 2011 Nanjwade BK, et al. This is an open-access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are credited.
 
Abstract
 
Solid lipid microparticles (SLMs) represent an alternative carrier system to traditional colloidal carrier such as emulsion, liposomes and polymeric micro and nanoparticles. The purpose of this research work was to develop and evaluate solid lipid microparticles of sirolimus for oral delivery. Sirolimus is an immunosupressive drug used to prevent transplant rejection and to treat auto immune diseases. It is a macrolide lactone produced by streptomyces hydroscopicus. It is extremely hydrophobic. Sirolimus solid lipid microparticles were prepared by hot homogenization technique. The matrix chiefly consisted of glyceryl monostearate and sodium taurocholate. The SLMs were studied for its particle size analysis, drug content, entrapment efficiency, in vitro release characteristics and also for stability analysis at different temperature and humidity conditions. Average particle size was found to be 21.40m. Drug content of SLMs determined by HPLC analysis was found to be 98.6 ± 0.31 while entrapment efficiency achieved was 98.02%. Drug release from the final formulation was found to be 90.3% in 90 min. SLMs formulated with glyceryl monostearate and sodium taurocholate can be used for oral delivery of hydrophobic drugs with in-vivo study still to be explored.
 
Keywords
 
Sirolimus; Immunosuppressant; Solid lipid microparticulates; Hot homogenization technique; Biocompatible lipid microparticles; Glyceryl monostearate
 
Introduction
 
Sirolimus (Rapamycin, Rapammune) is a macrolide lactone produced by streptomyces hydroscopicus. It is an immunosupressive agent used for the prophylaxis of renal allograft rejection. The drug was first isolated from a soil sample from Rapa Nui, an island in the south pacific, hence the prefix "Rapa". It is extremely hydrophobic having molecular weight 914.2 g/mol [1,2,3]. Sirolimus is neither calcineurin inhibitor (as are cyclosporine and tacrolimus) nor an anti metabolite (as are mycophenolate mofetil and azathioprine). Sirolimus has a novel mechanism of immunosuppressant action involving the suppression of T-lymphocyte proliferation through inhibition of the target of rapamycin protein kinase complex (TORC) [4]. Mammalian TORC is critical for cell cycle progression and cell proliferation. Blockade of TORC inhibits cytokine-mediated proliferation in T cells, B cells and mesenchymal cells, including smooth muscle cells [5].
 
In recent years, biocompatible lipid micro- and nanoparticles have been reported as potential drug carrier systems as alternative materials to polymers [6]. They can be considered as physiologically compatible, physicochemically stable and allowing a large-scale production at a relative low production cost than liposomes [7]. These micrometer-sized particles consist of a solid fat core based on naturally occurring lipids and stabilized by a layer of surfactant molecules on the surface [8]. SLM are characterized by their better bio-compatibility as compared to competing polymeric microparticles [9]. Solid lipid micro- or nanoparticles are in the form of solid lipids and provide an alternative option for encapsulating lipophilic compounds. Protein stabilization could be achieved by a suitable particle formulation or a polymer mixture [10]. Different methods can be adopted to prepare solid lipid micro- or nanoparticles. In one of the study, modified high shear homogenization and ultrasound method was utilized to formulate SLNs [11]. Reithmeier H and co- workers [12,13] in two different studies prepared peptide containing glyceryl palmitate microparticles as well as lipid microparticles by using modified solvent evaporation method and a melt dispersion technique without the use of organic solvent.
 
In this study, we prepared solid lipid microparticles by hot homogenization method [14,15]. The main aim of this investigation was to develop and evaluate solid lipid microparticles of sirolimus for oral delivery. The proposed sirolimus concentration in this formulation was chosen after assay and moisture content correction of API (sirolimus). Furthermore, in the present investigation, we aimed at fabricating SLM of sirolimus by using hot homogenization method and with easily available solid lipids such as glyceryl monostearate (GMS) and characterized it for assay and in vitro release.
 
Materials and Methods
 
Materials
 
Sirolimus (Zydus Cadila, Ahmedabad); Glyceryl monostearate (Fine organics Ltd., Mumbai, India); Sodium taurocholate, Acetone, Ethanol (All AR grade) and Acetonitile (ACN), H3PO4 (HPLC grade) were purchased from S.D. fine chemicals (Mumbai, India). All the excipients and reagents were used as received. Double distilled water was prepared freshly when ever required.
 
Preparation of solid lipid microparticles
 
Solid lipid microparticles were prepared by a hot homogenization technique. The formulations were optimized by first preparing blank microparticles by varying the content of GMS and sodium taurocholate and also by varying the processing parameters as shown in Table 1 and 2. Blank SLMs were prepared by first dissolving GMS in a mixture of acetone and ethanol (1:1). Organic solvents were completely removed using Buchi rotoevaporator (Buchi Laboretechnik AG, Flawil, Switzerland). Lipid layer was melted by heating 5C above the melting point of lipid. An aqueous phase was prepared by dissolving sodium taurocholate in double distilled water and heating to the same temperature as the oil phase. The hot aqueous phase was added to the oil phase, and homogenization was performed using Ultra Turrax high speed homogenizer for 2-3 min. Obtained micro emulsion was immediately dispersed in cold water (2-3C), under mechanical stirring. After a certain period, the samples were centrifuged at 10C, 5000 rpm for 10 min. Obtained micro emulsion was then lyophilized using Virtis ADVANTAGE, Wizard 2.0 Lyophilizer and obtained lyophilized powder was further evaluated. From the results obtained, blank formulation Lipo F/P 8006 was selected for final drug loaded SLM formulation (Table 3 and 4). Drug loaded SLMs were prepared by dissolving the sirolimus and GMS in a mixture of acetone and ethanol and the same method was followed as for the blank preparation.
 
Table 1: Formulation table for blank SLM formulations.
 
Table 2: Processing variables for blank SLM formulations.
 
Table 3: Observation of different trials of blank SLMs.
 
Table 4: Sirolimus loaded SLM formulation.
 
Particle size analysis
 
Particle size of the SLMs was determined immediately after dispersion, 1h later, and after 17h. The oily dispersible solution was resuspended in distilled water, prior to particle size determination. In a typical experiment, 150 l of the oily solution was mixed in 5 ml distilled water at 37C, using vortex for 30s. Then the particle size of the obtained suspension was determined at 37C for 200s by a Coulter N4 MD submicron particle size analyzer.
 
Assay (By HPLC)
 
Standard Preparation procedure: 25 mg of sirolimus pure sample was accurately weighed and dissolved in 100 ml of acetonitrile. 4 ml of the above stock solution was then diluted in 25 ml of acetonitrile to obtain a concentration of 40 g/ml. 20 l of this standard solution was injected by Hamilton 100 l syringe. The response of the preparation in terms of area under the two major peaks corresponding to isomer-C, Sirolimus standard was measured.
 
Sample preparation procedure: 10 capsules containing lyophilized powder of sirolimus lipospheres equivalent to 10 mg of drug was taken in 250 ml of volumetric flask and 150 ml of acetonitrile was added to it. It was then sonicated and volume was made up to 250 ml with acetonitrile. The solution was filtered with 0.45 filter paper and filled in the HPLC and measured for assay.
 
1. Mobile phase: 0.01%H3PO4: ACN (1:1)
 
2. Column: Kromasil/ C18 (150mm x 4.6mm) 5 m.
 
3. Flow rate: 2.0 ml/min
 
4. Detector: 277 nm
 
5. Column temperature: 50C
 
6. Sample cooler: 15C
 
7. Injection volume: 20 l
 
8. Retention time: Sirolimus - 11.5min, Isomer C - 12.2 min
 
Entrapment efficiency
 
The drug entrapment efficiency was determined by suspending known quantity of SLMs in methanol and stirring for few minutes. The free drug (unentrapped) which got dissolved in methanol was separated by centrifugation using a refrigerated centrifuge that runs for 10 min at 5000 rpm/min. The obtained methanolic phase was filtered through a 0.8 m membrane filter. Then the filtrate was analyzed by HPLC. The drug entrapment efficiency (EE) of the SLM was calculated by the equation:
 
 
Where Winitial drug = Weight of drug added to the system,
 
Wfree drug = Weight of free drug in the methanolic phase of system.
 
In vitro drug dissolution studies
 
Standard Preparation procedure: 25 mg of Sirolimus pure sample was accurately weighed dissolved in 100 ml of Acetonitrile. 2 ml of the above stock was then diluted in 250 ml of 0.4% SLS to obtain a concentration of 2 g/ml. 20 l of this standard solution was injected by Hamilton 100 l syringe. The response of the preparation in terms of area under the two major peaks corresponding to isomer-C, Sirolimus standard was measured.
 
Sample preparation procedure: In vitro dissolution was carried out by with USP type I apparatus using 500 ml of 0.4% SLS as the dissolution medium. 1 capsule (Microspheres equivalent to 1 mg of drug filled in each capsule) was placed in the each dissolution jar of the apparatus; dissolution was carried out at 120 rpm at 370 C for 90 mins. Known volume of the samples were withdrawn at predetermined time intervals and filled in HPLC vials, replaced with the same amount of fresh medium.
 
1 Mobile phase: 0.01%H3PO4: ACN (30:70)
 
2 Column: Kromasil/ C18 (150 mm x 4.6 mm) 5 m.
 
3 Flow rate: 0.5 ml/min
 
4 Detector: 277 nm
 
5 Column temperature: 50C
 
6 Sample cooler: 15C
 
7 Injection volume: 20 l
 
8 Retention time of sirolimus: 1min
 
Scanning electron microscopy
 
Scanning electron microscopy (SEM) is an electron optical imaging technique that provides photographic images and elemental information. SEM is useful for characterizing the morphology and size of microscopic specimens with particle size as low as 10-10 to 10- 12 m. The sample is placed in an evacuated chamber and scanned in a controlled pattern by an electron beam. Interaction of the electron beam with the specimen produces a variety of physical phenomena that, when detected, are used to form images and provide elemental information about the specimens.
 
Scanning electron microscopy (JSM 840 A) was used to study the surface morphology of the solid lipid microspheres. The samples were analyzed after they had been gold sputtered using 25 nm gold film thickness. Both samples were studied at magnifications at probe current of 20 KV.
 
Short-term stability study
 
Sirolimus solid lipid lipospheres were stored at temperature 2-8C, 25C/60%RH and 40C/75%RH for 30 days. Formulations at regular intervals were tested for physical changes, drug content and dissolution studies spectrophotometrically at 277 nm.
 
Results
 
Analytical method
 
Linearity of sirolimus in acetonitrile by HPLC: A simple method of estimation was developed in acetonitrile at 277 nm. The linearity of sirolimus is shown in Figure 1.
 
Development of HPLC estimation method for sirolimus: A precise, sensitive, reproducible High Performance Liquid Chromatographic method of estimation for sirolimus was developed. Further estimation of sirolimus was carried out by using newly developed HPLC method. A mixture of acetonitrile and 0.01% phosphoric acid (1:1) was used as a mobile phase on a C18 column. The flow rate was maintained at 2.0 ml/min. The peak height, area and retention time was calculated. The results are given in the Figure 2 and Table 5.
 
Particle size analysis
 
The effect of stirring speed on the properties of SLMs and the particle size distribution of SLMs is shown in Table 6 and 7 respectively.
 
Drug content using HPLC
 
Drug content of SLMs determined by HPLC analysis was found to be 98.60.31% (n=3)
 
Entrapment efficiency
 
The entrapment efficiency ( at zero day) of the microparticles (Lipo F 8006), was found to be 98.02%.
 
In vitro dissolution study
 
The dissolution study was carried out for the microspheres using 1 mg equivalent of drug in 0.4% SLS as dissolution media. The composition of dissolution media is (400 mg of sodium lauryl sulphate in 1000 ml distilled water) and pH is 9. The release profile of solid lipid microparticles is shown in Figure 3. Amount of drug released within 90 mins was found to be 90.30.58% (n=3).
 
Scanning electron microscopy
 
Scanning electron microscopy (SEM) studies were carried out to observe the surface morphology. Scanning electron microscopy (SEM) studies were carried out for pure drug as well as SLMs of sirolimus. SEM picture revealed that the pure drug was somewhat spherical with rough surface while the Sirolimus SLM was smooth and spherical. (Figure 4, 5)
 
Stability analysis of solid lipid sirolimus microsphere using HPLC
 
A precise, sensitive, reproducible HPLC method of estimation for sirolimus in the formulations was developed. The analysis was carried out soon after preparation and after 30 days (at 2-8C, 25C/60%RH and 40C/75%RH). Drug content after the stability period found is reported in Table 8. Amount of drug release from the SLMs of sirolimus is also reported in the Table 8 and is graphically depicted in the Figure 6.
 
Figure 1: Linearity of sirolimus.
 
Figure 2: HPLC chromatogram of pure sirolimus.
 
Figure 3: In vitro release profile of sirolimus solid lipid microspheres.
 
Figure 4: Scanning electron microscopy of sirolimus.
 
Figure 5: Scanning electron microscopy of SLMs of sirolimus.
 
Figure 6: Release rate profile of sirolimus SLMs after stability period.
 
Table 5: HPLC chromatogram parameters.
 
Table 6: Effect of stirring speed on properties of SLMs of sirolimus.
 
Table 7: Particle size distribution of formulation LIPO F 8006 (stirring speed 1000 rpm).
 
Table 8: Drug content and amount of drug release of SLMs at different stability conditions.
 
Discussion
 
In order to select the optimum formulation variables and to optimize the processing parameters, blank SLMs were prepared. Particle size analysis of blank SLMs shows that the optimum concentration of emulsifier (sodium taurocholate) to get the uniform sized microparticles is 0.2%w/v. An increase or decrease in concentration leads to the crystal formation. Particle size may also get affected due to the homogenization speed and the stirring rate (Table 2,3). Particle size gets decreased as the stirring rate increases. The optimum stirring speed was found to be 1000 rpm for 90 mins avoiding the crystal formation which is observed in case of the formulations with lower stirring rate and time.
 
SLMs were prepared by incorporating different amount (2.44 g and 5 g) of GMS. The higher amount of GMS showed satisfactory results. The higher drug content and entrapment efficiency with GMS is attributed to the high hydrophobicity resulting in increased accommodation of lipophilic drugs. Formulation Lipo F 8006 was subjected to in vitro release studies. The release study was performed in 0.4% SLS as dissolution media. The studies revealed that about 90.3 % of drug released from sirolimus SLMs after 90 mins at zero day. In vitro release study shows SLMs shows immediate release of the drug. After stability studies at different conditions (2-8C, 25C/60% RH, 40C/ 75% RH) for thirty days, drug content and drug release profiles revealed that the formulations were most stable at 2-8C and 25C/60% RH but unstable at 40C/ 75% RH (Table 8). Hence formulation should be kept at 2-8C and 25C/60% RH (cool and dry place). Presence of monoglyceride (GMS) may be responsible for the physical destabilization at higher temperature and humidity conditions. Lipids of less ordered crystal lattices such as GMS, though favored drug inclusion, were unstable due to the presence of monoglycerides.
 
Conclusions
 
Hot homogenization technique provides SLMs with higher drug content and entrapment efficiency by controlling the processing parameters. Hence, SLMs formulated with glyceryl monostearate and sodium taurocholate can be used for oral delivery of hydrophobic drugs with in-vivo study still to be explored.
 
Acknowledgement
 
The work has been supported by the KLE University, J.N. Medical College, Belgaum, Karnataka.
 
References
 
















 
 
This article
DOWNLOAD
» XML (kB)
» PDF (1,707 kB)
»
Export citation
»
Blog this article
   
CONTRIBUTE
» Write a response
» Read other responses
» Publishing with OPG
   
SHARE
» E-mail this article
» Print this article
» Rights and permissions
   
Share
EXPLORE
Related article at
» Pubmed
» DOAJ
» Scholar Google
 
 
 
| More
 
OMICS Publishing Group is the member of / publishing partner of/source content provider to
       
OMICS Publishing Group, An Open Access Publisher and Scientific Events Organizer for the Advancement of Science & Technology. All Published content, except where otherwise noted, is licensed under a Creative Commons Attribution License
Please ensure that you are using the latest version of Adobe reader. If you do not have this software installed on your system, you can download the free Adobe Reader by simply clicking on the following link: http://www.adobe.com/products/acrobat/readstep2.html
Best viewed in Mozilla Firefox | Google Chrome | Above IE 7.0 version Copyright 2013 OMICS Group, All Rights Reserved.